1: iMFF Setting

When there is paper of the same size attached to a designated location on the page, configure the scanner to memorize the location of the attachment and not detect multifeeds for that location.

Note that you first need to select [Check Overlapping (Ultrasonic)] for the multifeed detection setting in Specifying a Multifeed Detection Method [Multifeed] or the scanner driver's setup dialog box.

By selecting [4: Clear pattern], you can clear the overlapping patterns (length, location) that were previously memorized in Auto mode.

It can also be configured from the Software Operation Panel.

1: Manual mode

2: Auto mode 1

3: Auto mode 2

4: Clear pattern

2: No. of Paper Feed Retries

Configure this setting to change the number of feeding retries when a pick error occurs.

It can also be configured from the Software Operation Panel.

1 to 12 (times)

3: Pick Speed

When you experience frequent multifeeds and paper jams, the symptom may be improved by slowing down the speed at which the documents are fed (pick speed).

It can also be configured from the Software Operation Panel.

1: Normal

2: Slow

4: Soft Pick Setting

When you experience pick errors from the separator roller slipping on the paper, or paper jams from scanning thin papers of small widths, the symptom may be improved by bringing down the pick roller unit and keeping the unit at the lower position (disabling the Soft Pick Setting).

It can also be configured from the Software Operation Panel.

1: Disable

2: Enable

5: Manual Feed Timeout

Specify the waiting time to clear Manual Feed mode.

It can also be configured from the Software Operation Panel.

5, 10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 110, 120, 180, 240, 300, 360, 420, 480, 540, 600, 900, 1200, 1500, 1800, 1999 (seconds)

6: Paper Protection

Specify whether to enable or disable Paper Protection.

Enabling this setting reduces the risk of having your documents damaged in such ways, by stopping the scan when the scanner detects a document that is unusually warped.

You can specify the sensitivity to detect an abnormal feeding of documents when Paper Protection is enabled.

Documents are deformed (e.g. warped, bent, creased) when they are not being fed by the rollers properly. To detect such a symptom and stop the scan, select [1:Low] to only detect documents that are highly deformed, and [3:High] to also detect documents that are slightly deformed.

Paper Protection is disabled in Manual Feed mode.

Enable/Disable can also be configured from the scanner driver's setup dialog box or the Software Operation Panel. Note that priority is given to the scanner driver setting unless you have prioritized the operator panel setting.

Sensitivity can also be configured from the Software Operation Panel. Note that if you have prioritized the operator panel setting , priority is given to the operator panel setting.

1: Enable

2: Disable

Sensitivity:

1: Low

2: Normal

3: High

7: MF Quick Change

Enables you to switch whether or not to detect multifeed by a push of a button.

Priority is given to the scanner driver setting when [1: Disable] is selected.

When [2: Enable (Detect)] or [3: Enable (Ignore)] is selected, it switches between detecting/not detecting multifeed every time the [Eject] button is pressed. It can be switched during scanning.

For [2: Enable (Detect)], it detects multifeed by default and multifeed detection is performed according to the scanner driver setting.

For [3: Enable (Ignore)], it does not detect multifeed by default and multifeed detection is not performed regardless of the scanner driver setting.

1: Disable

2: Enable (Detect)

3: Enable (Ignore)

8: Alarm Volume

Specify whether or not to sound an alarm when an error such as multifeed or paper jam occurs.

It can also be configured from the Software Operation Panel.

1: OFF

2: Low

3: High

9: Stacker Positioning

Adjust the stacker position.

You can set the stacker at certain heights.

1: Movable

2: Fixed

10: Hopper Level

Change the hopper level during standby.

Selecting [1: Manual (Continuous)] switches the scanner to Manual Feed mode (Continuous Feed mode). The hopper level cannot be changed in Manual Feed mode (Single Feed mode).

Remove all documents from the hopper when you configure this item.

The hopper is set to [4: Lower] when you clear manual feeding (continuous).

1: Manual (Continuous)

2: Upper

3: Middle

4: Lower

11: Paper Separation Force

When you experience frequent multifeeds, pick errors or paper jams, take measures by adjusting the force to separate the papers.

Keep the default setting for normal use.

For details, refer to Adjusting the Paper Separation Force.

Low ←→ High

12: Alarm Sound Time

Specify the duration to ring the alarm in when errors such as multifeed and paper jam occur.

0.5, 1, 1.5, 2.0, 2.5 (seconds)

13: Button Sound Vol

Specify whether or not to make a sound when a button on the operator panel is pressed.

1: OFF

2: Low

3: High

(ring time fixed at 0.01 seconds)

14: Contrast

Specify the contrast for the LCD on the operator panel.

Weak ←→ Strong

15: Backlight ON

Specify the duration for which the backlight is ON.

Until initialization is complete after turning the power on, this item operates in [ON] regardless of the setting configured.

OFF, ON, 5, 10, 20, 30, 40, 50, 60, 90, 120, 150, 180, 210, 240, 270, 300 (seconds)

16: LED Blink Cycle

Specify the interval in which the Check LED flashes when (for Information) is displayed on the LCD.

0.5, 1.0, 1.5, 2.0, 2.5 (seconds)

17: Horizontal Scroll Speed

Specify the speed at which the display is horizontally scrolled.

The displayed item is scrolled horizontally when the text does not fit in the LCD.

1: Fast

2: Normal

3: Slow

4: OFF

18: Operation Panel Timeout

Specify the time to return to the [Ready] screen from [Hopper Level] or [Paper Separation Force].

Note that this option is only available when you display [Hopper Level] or [Paper Separation Force] from the [Ready] screen by using a shortcut key.

To display [Hopper Level] by shortcut key, press the [Eject] button and either the [] or [] button at the same time when [Ready] is displayed.

Note that the [Hopper Level] screen is not displayed unless the two buttons are pressed simultaneously.

To display the [Paper Separation Force] screen by shortcut key, press the [] or [] button when [Ready] is displayed.

OFF, 5 to 9 (seconds)

19: Language

Specify the language in which data is displayed.

1: Japanese

2: English

3: French

4: German

5: Italian

6: Spanish

7: Russian

8: Chinese (S)

9: Chinese (T)

10: Portuguese

11: Turkish

12: Korean

13: Arabic

20: Prioritize Panel Settings

Prioritize the operator panel setting for Paper Protection.

When [1: Paper Protection] is selected, the Paper Protection setting of the operator panel is prioritized.

When [2: Clear] is selected, the Paper Protection setting is no longer prioritized.

1: Paper Protection

2: Clear

(*3)

21: Cleaning

Use this setting when you clean the scanner.

For more details, refer to Daily Care.

1: Sheet

2: Wipe

22: Test Print

Use this option to run a test print when the Imprinter is installed.

For more details, refer to the "fi-680PRF/PRB Imprinter Operator's Guide".

No. of sheets scanned:

1: Single sheet only

2: Multiple sheets

Print: (*5)

1: Front Side

2: Back Side

Print Pattern:

1: (L)ABCDEFGHIJKLMNOPQRSTUVWX YZ[]^_`00000000

2:(L)abcdefghijklmnopqrstuvwxyz{|}¯00000000

3:(L)!"#$%&'()*+,-./0123456789:;<=>?@00000000

4:(P)ABCDEFGHIJKLMNOPQRSTUVWXYZ[]^_`00000000

5:(P)abcdefghijklmnopqrstuvwxyz{|}¯00000000

6:(P)!"#$%&'()*+,-./0123456789:;<=>?@00000000

Test Print:

1: Yes

2: No

23: Show/Clear Counters

Check the replacement cycle of the consumables and the total page count of the maintenance parts.

Also use it to reset the counter when you have replaced the consumables or performed cleaning.

Brake Roller / Pick Roller / Separator Roller / Assist Roller / Cleaning / Total sheets scanned

Ink Level:Front/Ink Level:Back (when the imprinter option is installed)

24: Ope. Panel Initialization

Initialize the settings of the operator panel,

except for the language setting and any items without a factory default setting.

1: Yes

2: No

25: Doc Counting Mode

Compare the number of sheets scanned in Doc Counting Mode and Doc Count Check Mode.

—

26: Low-speed Feed Mode

Select whether to perform a slow scanning speed, in order to protect the documents.

It can also be configured from the Software Operation Panel.

1: Enable

2: Disable

27: Automatic Separation Control

Select whether to control the paper separation force automatically for each document type.

It can also be configured from the Software Operation Panel.

1: Enable

2: Disable

28: Stacking Control

Set the control for ejecting documents when scanning documents with a document length of 138 mm or shorter.

It can also be configured from the Software Operation Panel.

1: Stackability Emphasis

2: Normal

3: Speed Emphasis