Set save destinations (folders on the network) to which scanned images will be saved when using DirectScan.

Up to 25 save destinations can be added.

Display Name

Set a name for the save destination.

Enter a display name within 48 characters.

You cannot set the same name as a display name that is already registered.

The space before or after the character string is ignored.

Destination Type

Set the type of the save destination.

• Network Directory

  This is the factory default setting.

  When [Network Directory] is selected, specify the following items:

  • Host Name/IP address

    The host name, FQDN, or IP address can be set for this item.

    The space before or after the character string is ignored.

    When a path delimiter appears at the beginning of the value, the delimiter will be removed.

    ATTENTION

    • Note that an IPv6 address is not supported.

    • Supported versions of SMB range from SMB 2.0 to SMB 3.0.2.

    • Saving images to a server where data access is encrypted in the share settings or a folder where a DFS is used is not supported.

    HINT

    When entering a host name, the DNS servers need to be set on the scanner.

  • Save Destination Path

    The spaces before and after the character string and "/" prefix are ignored.

    "" will be replaced with "/". When the first character is "", the character will be replaced with "/" and the leading "/" will be deleted.

  • Username

    Set the user name used to connect to the save destination.

    You can also set the name in the "UserName@Domain" or "DomainUserName" format.

    To use the Active Directory domain user name as a user name for authentication, specify the Active Directory domain name as the user name only or the domain name to be included in the user name. To authenticate a user as a local user, specify the device name as the domain name to be included in the user name.

    The space before or after the character string is ignored.

  • Password

    • Enable

      The factory default setting is set to on.

      When [Enable] is set to ON, enter the password for the user name used for connecting to the save destination.

      Spaces before and after the character string are maintained.

• FTP

  When [FTP] is set, specify the following items:

  • Host Name/IP address

    The host name, FQDN, or IP address can be set for this item.

    The space before or after the character string is ignored.

    ATTENTION

    Note that an IPv6 address is not supported.

    HINT

    When entering a host name, the DNS servers need to be set on the scanner.

  • Port Number

    The factory default setting is "21".

  • Connect Mode

    Set the connect mode used to connect to the FTP server.

    • Active Mode

    • Passive Mode

      This is the factory default setting.

  • Save Destination Path

    The spaces before and after the character string and "/" prefix are ignored.

    "" will be replaced with "/". When the first character is "", the character will be replaced with "/" and the leading "/" will be deleted.

  • Username

    Set the user name used to connect to the save destination.

    You can also set the name in the "UserName@Domain" or "DomainUserName" format.

    The space before or after the character string is ignored.

  • Password

    • Enable

      The factory default setting is set to on.

      When [Enable] is set to ON, enter the password for the user name used for connecting to the save destination.

      Spaces before and after the character string are maintained.

• FTPS

  When [FTPS] is selected, specify the following items:

  • Host Name/IP address

    The host name, FQDN, or IP address can be set for this item.

    The space before or after the character string is ignored.

    ATTENTION

    Note that an IPv6 address is not supported.

    HINT

    When entering a host name, the DNS servers need to be set on the scanner.

  • Encryption

    Set the encryption method for communications used when connecting to the FTPS server.

    • Explicit Encryption (Explicit Mode)

      This is the factory default setting.

    • Implicit Encryption (Implicit Mode)

  • Validate server certificates

    Set whether to validate server certificates using CA certificates registered on the scanner.

    The factory default setting is set to off.

    HINT

    When using a CA certificate, you can register the certificate in fi Series Network Settings.

    For details, refer to Network Settings (fi Series Network Settings).

  • Port Number

    Depending on the setting for [Encryption], the initial value changes as follows:

    • When [Encryption] is [Explicit Encryption (Explicit Mode)], the initial value is "21".

    • When [Encryption] is [Implicit Encryption (Implicit Mode)], the initial value is "990".

    The factory default setting is "21".

  • Save Destination Path

    The spaces before and after the character string and "/" prefix are ignored.

    "" will be replaced with "/". When the first character is "", the character will be replaced with "/" and the leading "/" will be deleted.

  • Username

    Set the user name used to connect to the save destination.

    You can also set the name in the "UserName@Domain" or "DomainUserName" format.

    The space before or after the character string is ignored.

  • Password

    • Enable

      The factory default setting is set to on.

      When [Enable] is set to ON, enter the password for the user name used for connecting to the save destination.

      Spaces before and after the character string are maintained.

  HINT

  The only connection mode for connecting to the FTPS server is "Passive Mode".

• SFTP

  When [SFTP] is selected, specify the following items:

  • Host Name/IP address

    The host name, FQDN, or IP address can be set for this item.

    The space before or after the character string is ignored.

    ATTENTION

    Note that an IPv6 address is not supported.

    HINT

    When entering a host name, the DNS servers need to be set on the scanner.

  • Port Number

    The factory default setting is "22".

  • Save Destination Path

    The spaces before and after the character string and "/" prefix are ignored.

    "" will be replaced with "/". When the first character is "", the character will be replaced with "/" and the leading "/" will be deleted.

  • Authentication Method

    Set the authentication method.

    When [Public Key Algorithm] is [Disabled], specify [Password authentication].

    When [Public Key Algorithm] is other than [Disabled], select one of the following:

    • Password authentication

      This is the factory default setting.

    • Public Key Authentication

      The public key algorithm used when the encryption key is generated is displayed in [Public Key Algorithm].

      This setting can be configured when an encryption key has already been generated for the scanner.

      HINT

      If you are using an encryption key, you can register the key in fi Series Network Settings.

      For details, refer to Network Settings (fi Series Network Settings).

  • Username

    Set the user name used to connect to the save destination.

    You can also set the name in the "UserName@Domain" or "DomainUserName" format.

    The space before or after the character string is ignored.

  • Password

    This setting can be configured when [Password authentication] is selected for [Authentication Method].

    • Enable

      The factory default setting is set to on.

      When [Enable] is set to ON, enter the password for the user name used for connecting to the save destination.

      Spaces before and after the character string are maintained.